How to Choose an Electric Vacuum Gripper for a Collaborative Robot?
Share
Collaborative robots, commonly known as cobots, are increasingly used in automated handling, assembly, packaging, and small-part manufacturing. Their compact design and flexible deployment make them suitable for a wide range of industrial applications.
When a cobot needs to pick up and transfer workpieces, an electric vacuum gripper provides an integrated gripping solution without requiring an external compressed-air supply. However, selecting the right gripper requires more than matching payload ratings. Engineers must also consider workpiece characteristics, vacuum performance, electrical compatibility, and robot operating conditions.
This guide explains the main factors involved in selecting an electric vacuum gripper for a collaborative robot. If you are comparing different vacuum-generation methods, see our guide to Electric vs Pneumatic Vacuum Grippers: Which Is Better for Robot Pick-and-Place? for a comparison of their system architectures and integration requirements.
Understand the Payload Limits of Your Collaborative Robot
Before selecting a vacuum gripper, check the collaborative robot's rated payload. This specification covers the load supported by the robot under specified operating conditions, not just the weight of the workpiece.
The total payload includes the gripper, mounting components, accessories, and workpiece. The load's center of gravity and wrist moments must also remain within the robot manufacturer's limits.
Calculate the Complete Payload
Consider a collaborative robot with a rated payload of 5 kg. If the complete gripper assembly weighs 0.8 kg, the nominal remaining payload allowance is:
Available payload = 5 kg − 0.8 kg = 4.2 kg
However, this does not automatically mean the robot can handle a 4.2 kg workpiece in every configuration. The actual allowable load also depends on mounting position, center of gravity, and robot motion.
A second factor is the distance between the load and the robot flange. A long mounting adapter can create a greater wrist moment than a more compact assembly, even when the overall weight is relatively low.
Engineers should therefore check the robot manufacturer's payload diagrams and permitted center-of-gravity and moment limits rather than relying on the rated payload alone.
Consider the Weight and Dimensions of the Vacuum Gripper
The gripper's weight and physical dimensions affect both the robot's available payload and the installation space at the end of the robot arm.
A compact, lightweight gripper can preserve more payload capacity and provide greater flexibility when integrating the end effector into a restricted workspace.
Three practical considerations are particularly important:
- Weight: A lighter gripper leaves more payload capacity available for the workpiece and mounting accessories.
- Dimensions: The gripper must fit the available installation space and reach the intended pickup position.
- Mounting geometry: Adapters and mounting structures should not create excessive distance between the robot flange and the load's center of gravity.
The complete arrangement should also provide sufficient clearance around surrounding fixtures and equipment. Choosing the smallest gripper is not necessarily the best solution if its mounting configuration limits accessibility or gripping performance.
Match the Suction Cup to the Workpiece Surface and Geometry
The suction cup directly contacts the workpiece and determines whether the vacuum system can establish a reliable seal.
Its size and configuration should match the actual surface condition and available contact area. A larger suction cup does not necessarily provide better gripping if the workpiece cannot form a suitable seal.
Different workpiece conditions create different sealing requirements:
| Workpiece Condition | Selection Consideration |
|---|---|
| Smooth, flat surfaces | Generally provide favorable sealing conditions |
| Curved surfaces | May require cups designed to accommodate curvature |
| Rough or uneven surfaces | Require attention to sealing performance |
| Porous materials | May allow continuous air leakage |
| Grooves or openings | Can create leakage paths |
| Contaminated surfaces | Dust, oil, and moisture may affect the seal |
The suction cup should provide sufficient effective contact area without interfering with surrounding features.
The important point is to evaluate the actual production surface, not just the nominal workpiece material. A cup that performs well on a clean metal surface may behave differently when the same surface is covered with machining oil or dust.
Evaluate Vacuum Performance and Required Holding Force
Once the suction cup is selected, the next step is to determine whether the gripper can provide sufficient holding performance.
Two important specifications are maximum vacuum and flow rate. They describe different aspects of the vacuum system and should be evaluated together.
Maximum vacuum indicates the highest vacuum level achievable under specified conditions, while flow rate describes the system's capacity to move air. Both influence gripping performance, particularly when leakage occurs at the suction-cup interface.
Understand the Relationship Between Vacuum and Holding Force
The theoretical suction force can be estimated using:
F = ΔP × A
Where:
- F: Theoretical suction force in newtons (N).
- ΔP: Magnitude of the pressure difference between the inside of the suction cup and the surrounding atmosphere in pascals (Pa).
- A: Effective suction area in square meters (m²).
A greater pressure difference or effective suction area produces a higher theoretical suction force.
However, actual gripping performance may be lower because of air leakage, suction-cup deformation, and surface irregularities.
There is also an important distinction between normal holding force and resistance to sliding. When handling a workpiece horizontally or vertically, friction and the direction of the applied load must also be considered.
Evaluate Maximum Vacuum and Flow Rate Together
Maximum vacuum and rated flow rate are generally specified under different operating conditions. They should not be assumed to occur simultaneously.
For example, a system may achieve high vacuum under a sealed condition but struggle to maintain it when the workpiece surface allows continuous air leakage. Sufficient flow capacity helps compensate for leakage, depending on the pump's performance characteristics.
Where available, engineers should evaluate the pump's performance curve to determine the actual airflow at the required vacuum level.
The main parameters to check are:
- Maximum vacuum under specified test conditions.
- Flow rate at the required operating vacuum.
- Air leakage at the suction-cup interface.
- Vacuum buildup and holding performance.
This is more useful than selecting a gripper based solely on its highest published vacuum rating.
Check the Electrical Power Requirements
Electric vacuum grippers use integrated electric pumps to generate vacuum, eliminating the need for an external compressed-air supply for these models.
However, electrical compatibility must be confirmed before connecting the gripper to a collaborative robot.
Matching the nominal voltage is only the first step. Engineers must also verify current requirements, available power, connectors, and electrical interfaces.
The VS30A, VS50A, and VS70A models from Vacuum Lifting Solution all use 24V DC power.
Their published electrical specifications are:
| Model | Voltage | Current | Power |
|---|---|---|---|
| VS30A | 24V DC | 0.1A | 2.4W |
| VS50A | 24V DC | 0.1A | 2.4W |
| VS70A | 24V DC | 0.2A | 4.8W |
Before connecting a gripper directly to the robot, check:
- Whether the robot provides a compatible 24V DC auxiliary output.
- Whether its available current is sufficient.
- Whether startup or transient current requires additional capacity.
- Whether a separate external power supply is necessary.
If the robot's auxiliary output cannot support the gripper, a suitable external supply can provide operating power while the robot handles compatible control signals.
Connector type, pin assignment, and cable routing should also be checked to avoid connection errors and interference with robot movement.
Verify Control Interfaces and Release Functions
Besides electrical power, engineers must confirm how the robot and vacuum gripper coordinate their gripping and release operations.
The control interface determines how the gripper responds to external signals and whether the robot can receive information about the gripping condition. Signal definitions and wiring must be verified for the selected model.
Understand the Control Sequence
The operation of an integrated electric vacuum gripper depends on its internal control design.
For the VS30A and VS50A, vacuum generation is managed by the integrated control system after power is applied. A separate release control signal is provided for releasing the workpiece.
The VS70A documentation identifies an additional I/O control signal, whose exact function should be confirmed against the wiring diagram for the selected model.
Check Model-Specific Wiring
For the VS30A and VS50A, the published wiring descriptions identify:
- Brown: 24V+
- Blue: 24V−
- Black/yellow: Release control signal
For the VS70A, the black/yellow wire is identified as an I/O control signal. Its specific function should be verified using the corresponding wiring documentation.
Before integration, engineers should confirm signal voltage levels, electrical logic, connector pin assignments, and compatibility with the robot controller.
Don't Confuse Release Control with Vacuum Feedback
These are two different functions.
A release signal allows the robot to activate the gripper's release mechanism. Vacuum feedback, on the other hand, tells the controller whether the required gripping condition has been achieved.
The published wiring descriptions for these three models do not specify a separate electrical vacuum-status output. If the application requires an independent vacuum-achieved signal, engineers should confirm its availability or consider a compatible external vacuum sensor.
This distinction is important when designing automated pickup sequences, especially when the robot must verify successful gripping before moving the workpiece.
Consider Robot Motion, Cycle Time, and Collaborative Safety
A gripper that performs well during stationary testing may behave differently when installed on a moving collaborative robot.
The selected gripper must maintain suitable holding performance throughout the robot's intended movement, including acceleration, deceleration, and changes in orientation.
A few operating conditions deserve particular attention:
- Acceleration and deceleration: Rapid changes in speed introduce additional forces at the gripping interface.
- Orientation changes: Rotational and vertical movements can affect workpiece stability.
- Cycle frequency: Repeated pickup and release operations must remain consistent throughout the production cycle.
- Vacuum response time: Pump buildup and release time contribute to the overall handling cycle.
A stationary pickup test alone is therefore insufficient. The complete robot path and workpiece orientation should be included in application testing.
Collaborative operation also requires an application-specific safety assessment. Workpiece weight, sharp edges, potential dropping, and pinching points may require additional monitoring or protective measures. Engineers should also consider how the system responds to power interruption or unexpected vacuum loss.
Use a Cobot Integration Checklist Before Final Gripper Selection
Before finalizing the selection, engineers should confirm that the gripper, robot, and workpiece are compatible as a complete system.
A practical integration checklist helps identify potential problems before installation and provides a consistent basis for comparing different electric vacuum gripper models.
| Integration Item | What to Confirm |
|---|---|
| Robot Payload | Combined weight and permitted wrist moments |
| Mechanical Compatibility | Robot flange, mounting dimensions, and installation clearance |
| Workpiece Compatibility | Surface condition, geometry, and sealing performance |
| Vacuum Performance | Required vacuum level, operating flow, and holding performance |
| Electrical Supply | 24V DC compatibility, current, and power capacity |
| Control Interface | I/O wiring, release function, and vacuum feedback |
| Motion and Safety | Robot movement, workpiece stability, and fault response |
Electric Vacuum Gripper Options from Vacuum Lifting Solution
Vacuum Lifting Solution offers three electric vacuum gripper models with different payload and vacuum specifications.
| Model | Supply / Current / Power | Maximum Payload | Vacuum / Flow Rate | Dimensions / Weight |
|---|---|---|---|---|
| VS30A-S1-M1.5 | 24V DC / 0.1A / 2.4W | 6 kg | −60 kPa / ≥1.2 L/min | 50 × 30 × 85 mm / 318 g |
| VS50A-S1-M1.5 | 24V DC / 0.1A / 2.4W | 6 kg | −60 kPa / ≥1.2 L/min | 50 × 50 × 70 mm / 360 g |
| VS70A-S1-M1.5 | 24V DC / 0.2A / 4.8W | 20 kg | −70 kPa / ≥3 L/min | 83 × 75 × 59 mm / 670 g |
The three models offer different combinations of size, weight, and vacuum performance:
- VS30A: A compact 318 g configuration with a published maximum payload of 6 kg.
- VS50A: The same published maximum payload with a different housing configuration and a weight of 360 g.
- VS70A: A higher specified payload of 20 kg, with higher maximum vacuum and flow-rate specifications.
These ratings provide an initial reference for product selection, but maximum payload should not be interpreted as the recommended workpiece weight for every collaborative robot.
You can explore the complete range of Electric Vacuum Grippers from Vacuum Lifting Solution to compare the available models and their specifications.
Conclusion
Choosing an electric vacuum gripper for a collaborative robot requires more than matching payload ratings. Robot capacity, gripper dimensions, suction-cup compatibility, vacuum performance, electrical supply, and control interfaces all influence the final selection.
The most suitable gripper is one that meets the application's mechanical, electrical, and operating requirements while providing reliable pickup and release performance. If you are evaluating an electric vacuum gripper for a collaborative robot or another automated handling system, contact our team at vacuumliftingsolution@gmail.com to discuss your workpiece, robot specifications, and integration requirements.
FAQ
The following questions address common considerations when integrating electric vacuum grippers with collaborative robots.
The key is to evaluate the gripper as part of the complete robotic system, rather than selecting it based on a single specification.
What Size Vacuum Gripper Do I Need for a Collaborative Robot?
The appropriate gripper depends on workpiece weight, surface condition, suction area, robot payload capacity, and motion requirements. Remember to include the gripper and mounting components when calculating the total payload.
Does a Collaborative Robot Need a Special Vacuum Gripper?
Not necessarily. An electric vacuum gripper can be used if its mounting arrangement, payload, electrical supply, and control interface are compatible with the robot. The complete application must also meet relevant safety requirements.
Can a 24V Electric Vacuum Gripper Connect Directly to a Cobot?
It depends on the robot's electrical configuration. The robot must provide a compatible 24V DC supply with sufficient current capacity. Otherwise, a suitable external power supply may be required.
How Does Gripper Weight Affect Collaborative Robot Payload?
Gripper weight reduces the payload available for the workpiece. Its mounting position and dimensions also influence the moment applied to the robot wrist.
How Do You Prevent Workpieces from Dropping During Robotic Handling?
Select a suitable suction cup and verify that the vacuum system can maintain sufficient gripping performance under actual operating conditions. Consider robot acceleration, workpiece orientation, vacuum monitoring, and appropriate responses to unexpected vacuum loss.